VTL30050
VTL30050 UV-cure spray lacquer for furniture, 50 gloss
Clear UV-cure spray lacquer for furniture, semi-gloss (50 gloss). Flows out very well and gives a highly transparent film that resists physical and chemical attack. Cures only under UV lamps — it will not dry on its own.
- Clear topcoat for furniture fronts, panels and parts on lines with UV curing (official: «for furniture»)
- Profiled parts, mouldings and frames that can't go through a roller coater or curtain coater (by analogy with the VTL30040 schedule)
Mix calculator
Ratio 100 : 20.0
| Component | Weigh out |
|---|---|
| VTL30050part A | 417 g |
| S11Thinner | 83.3 g |
| Total | 500 g |
Covers roughly 4.17 m² at 120 g/m².
Ask about VTL30050
Answers are based on the VTL30050 data and the products it mixes with.
Mixing matrix
- S11Thinner% by weight: 15–20 %recommended
Default — follows Technocolor's schedule for the VTL300xx UV spray lacquers.
Catalog lists S11 as medium-evaporation (polyester gloss lacquer thinner). Flash off 5–10 min at 30–35 °C before the lamps.
- S31Thinner% by weight: 10–20 (typ. 15) %recommended
General-purpose option at 18–25 °C if S11 isn't on hand.
Let the solvent flash off completely before UV.
- % by weight: 10–15 %recommended
Short line or little flash-off time; small and profiled parts.
On large flat panels may give orange peel and dry overspray — gloss will look uneven.
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Thinner | S11 | 15–20 %recommended | — | Default — follows Technocolor's schedule for the VTL300xx UV spray lacquers.Catalog lists S11 as medium-evaporation (polyester gloss lacquer thinner). Flash off 5–10 min at 30–35 °C before the lamps. |
| Thinner | S31 | 10–20 (typ. 15) %recommended | — | General-purpose option at 18–25 °C if S11 isn't on hand.Let the solvent flash off completely before UV. |
| Thinner | S30 / S13 | 10–15 %recommended | — | Short line or little flash-off time; small and profiled parts.On large flat panels may give orange peel and dry overspray — gloss will look uneven. |
Percentages are per 100 parts of component A.
Characteristics
- Gloss
- 50 GU (60°)official
- Components
- 1K, UV-curing (no hardener)recommended
- Pot life
- not applicable (1K); keep shielded from lightrecommended
- Solids
- 50–90 % by weight, as supplied (expected range)recommended
- Viscosity · Spray target
- 16–22 s
- Viscosity · Why ru
- Не опубликовано. Прозрачный лак для распыления HVLP/обычным краскопультом обычно наносят при ~16–22 с DIN4; разбавляйте по месту.
- Drying · Flash-off before UV
- 5–10 minrecommended
- Drying · UV cure
- 3 × 80–120 W lamps, belt 10 m/minrecommended
- Drying · Before sanding
- immediately after UV cure and coolingrecommended
- Drying · Conditions
- line conditions; material at ~20 °C
- Chemical resistance
- stated, not rated («физико-химическая стойкость»)official
- Flow
- excellent levelling («Отлично растекается»)official
- Clarity
- high transparency («высокая прозрачность»)official
Application
Conventional spray
- Consumption
- 110–130 g/m²official
- Nozzle
- 1.4–1.6recommended
- Pressure · air
- 3–4 bar at gun inletrecommended
- Spray viscosity
- 16–22 s DIN4recommended
- Wet film
- 100–130recommended
- Coats
- 1–2recommended
- Flash-off
- 5–10recommended
- Recoat
- after UV cure + sandingrecommended
- Sanding between coats
- P320–P400recommended
110–130 g/m² is the Technocolor figure; the rest are recommendations.
HVLP
- Consumption
- 110–130 g/m²official
- Nozzle
- 1.4–1.5recommended
- Pressure · air
- 2–2.2 bar inlet (trigger pulled); air cap ≤0.7 barrecommended
- Spray viscosity
- 16–20 s DIN4recommended
- Flash-off
- 5–10recommended
15–20 cm gun distance, 50–75 % overlap, fan fully open.
Airmix (air-assisted airless)
- Consumption
- 110–130 g/m²official
- Nozzle
- 0.18–0.23recommended
- Pressure · fluid
- 40–70 barrecommended
- Pressure · air
- 1–2 barofficial
Per Technocolor's methods page, airmix suits topcoats better than airless.
Electrostatic
- Consumption
- 110–130 g/m²official
- Nozzle
- as airmix/conventionalrecommended
Parts must be earthed (wood needs moisture or a conductive primer); check the lacquer's conductivity first.
Process and compatibility
- Substrate preparation
- Sanded, dust-free clear UV primer (VTS30006, VTS60019; VTS40041 on profiles).recommended
- Sanding
- primer: P240→P320 (flat) or K120/K150 brushes (profiles) before the lacquerrecommended
- Temperature and humidity
- material 18–25 °C; flash-off 30–35 °Crecommended
- Don'ts
- Don't send it under the lamps before the solvent has flashed off
- Don't expect it to dry without UV — it won't
- Don't keep it in clear containers or in daylight
- Don't add PU hardeners — it's single-pack
- Don't polish the final 50-gloss coat — the sheen goes patchy
Storage
- Storage temperature
- 5–25 °C, darkrecommended
Safety: UV acrylate monomers are strong skin sensitisers: nitrile gloves, goggles and a respirator for spraying. Shield eyes and skin from the UV lamps. (Recommendation, not from a Technocolor SDS.)
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- official page: properties, spray 110–130 g/m², 50 gloss, for furniture
- sibling VTL30040 page: identical properties text and consumption
- UV baguette schedule: sibling VTL30040 + S11 20 %, 150 g/m², over VTS40041, flash-off 30–35 °C 5–10 min, UV 3×80–120 W 10 m/min
- UV anegri schedule: UV primer sanding P240–P320, VTL30100 pre-dry 30–35 °C 5 min, UV 3×80–120 W 10 m/min
- application methods (UV roller 98–100 % solids; airmix air 1–2 bar; electrostatic with any system)
- characteristics vocabulary (gloss at 60° for mid-gloss)
- clear UV spray primer (candidate base coat)
- clear UV spray primer (candidate base coat)
- dealer search — no result
Not covered by the sources
- No dealer page: t-colormarket.ru search for VTL30050 returns nothing (shop has no UV category); woodonline.ru, lakokraska31.ru, ndom31.ru also return nothing
- No TDS/SDS PDF found (web search budget exhausted in this session; direct dealer probes and Bing RSS empty)
- Not in the Technocolor 2025–2026 catalog transcripts (catalog has no UV section)
- Solids % (only an expected range derived)
- Viscosity as supplied, density
- Official thinner and thinning ratio for VTL30050 (only sibling VTL30040 schedule + catalog UV-thinner suitability)
- Flash-off and UV dose (lamp type, mJ/cm²) for this code — only sibling schedules
- Shelf life, storage temperature, packaging
- Lightfastness/yellowing, elasticity, adhesion data
- No official finishing schedule uses VTL30050
- Thinner ratio by volume (no source gives it; the S11 20 % in the sibling schedule doesn't state its basis)
- TDS web search could not be re-run in the verification pass (search budget exhausted); t-colormarket.ru search for VTL30050 re-checked 2026-10-05: no result, shop has no UV category