XGC06D
XGC06D Exterior lacquer/primer, 60 gloss — 3-in-1 waterborne system: impregnation, primer and topcoat in one
Three-in-one exterior wood finish: impregnation, primer and topcoat from one tin. High weather resistance, easy to apply, tints with XHT. Semi-gloss, 60 gloss.
- windows and doors (dimensionally stable joinery)
- cladding, fascia and fence boards
- garden furniture, gazebos, pergolas
- clear or tinted exterior finishing of softwoods and hardwoods
Mix calculator
Ratio 100 : 0.0
| Component | Weigh out |
|---|---|
| XGC06Dpart A | 500 g |
| waterThinner | 0.0 g |
| Total | 500 g |
Covers roughly 5.56 m² at 90 g/m².
Ask about XGC06D
Answers are based on the XGC06D data and the products it mixes with.
Mixing matrix
- waterThinner% by weight: 0–5 %recommended
only if needed — heat, dry air, spitting gun
Water only. Never add solvent thinners (S50/S80 etc.).
- XTC3Additive% by weight: 0–2 %datasheet
retarder — heat, large panels, brushing
Milesi XTC 3 — not found on the Technocolor t-color.ru range.
- XHT8 / XHT9 / XHT10 / XHT12 / XHT16 / XHT17 / XHT18 / XHT19Additive% by weight: 5–15 (typ. 10) %recommended
tinted finish; pigment adds UV protection
Tinting knocks the gloss down a bit. Mix thoroughly; one batch for the whole job.
- XTC2Additive% by weight: 0.1–1 %datasheet
anti-foam — bubbles from brush/roller
Milesi; not on the Technocolor range.
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Thinner | water | 0–5 %recommended | — | only if needed — heat, dry air, spitting gunWater only. Never add solvent thinners (S50/S80 etc.). |
| Additive | XTC3 | 0–2 %datasheet | — | retarder — heat, large panels, brushingMilesi XTC 3 — not found on the Technocolor t-color.ru range. |
| Additive | XHT8 / XHT9 / XHT10 / XHT12 / XHT16 / XHT17 / XHT18 / XHT19 | 5–15 (typ. 10) %recommended | — | tinted finish; pigment adds UV protectionTinting knocks the gloss down a bit. Mix thoroughly; one batch for the whole job. |
| Additive | XTC2 | 0.1–1 %datasheet | — | anti-foam — bubbles from brush/rollerMilesi; not on the Technocolor range. |
Percentages are per 100 parts of component A.
Characteristics
- Components
- 1K (single component)recommended
- Pot life
- not applicable (1K)recommended
- Gloss
- 60 GU (60°)official
- Properties (Milesi)
- Thixotropic finish on special resins that wet and penetrate the wood; very elastic, good blocking resistance, high UV and weather resistance.datasheet
- Elasticity
- excellent elasticity ('ottima elasticità')datasheet
- Lightfastness
- high UV resistancedatasheet
- Chemical resistance
- weather resistance high ('высокая атмосферостойкость')official
- Thixotropy
- yes — 'finitura tixotropica'datasheet
- Min dry film (µm)
- 90 µmdatasheet
- Drying · Between coats (h)
- min 12 hdatasheet
- Drying · Fully dry
- min 24 hdatasheet
- Drying · Conditions
- Milesi cycle times; ambient conditions not stated (assume ~20 °C, 60–65 % RH)
Colours
- XHT8 · Hydrocrom impregnation, walnut
- XHT9 · Hydrocrom impregnation, oak
- XHT10 · Hydrocrom impregnation, fir
- XHT12 · Hydrocrom impregnation, teak
- XHT16 · Hydrocrom impregnation, pale walnut
- XHT17 · Hydrocrom impregnation, antique walnut
- XHT18 · Hydrocrom impregnation, mahogany
- XHT19 · Hydrocrom impregnation, myrtle
Application
HVLP
- Nozzle
- 1.8–2.2 mmrecommended
- Pressure · air
- 1.8–2.2 barrecommended
- Consumption
- 80–100 g/m²official
- Coats
- 3 coatsrecommended
- Flash-off
- 20–40 minrecommended
- Recoat
- min 12 h (Milesi cycle C4/L3, XGC 63)datasheet
- Sanding between coats
- P180–P220 by hand before the final coatdatasheet
15–20 cm gun distance, 50 % overlap. First coat acts as the impregnation — let it soak, flood end grain.
Conventional spray
- Nozzle
- 1.9–2.5 mmdatasheet
- Pressure · air
- 3–4 bardatasheet
- Consumption
- 80–100 g/m²official
Milesi figures for the whole Hydrocrom line.
Airmix (air-assisted airless)
- Nozzle
- 0.23–0.28 mmdatasheet
- Pressure · fluid
- 80–100 bardatasheet
- Pressure · air
- 1–2 bardatasheet
Milesi: stainless wetted parts, pump ratio ≥ 28:1, ≥ 4 l/min. 40° fan for window profiles is our suggestion.
Airless
- Nozzle
- 0.23–0.28 mmdatasheet
- Pressure · fluid
- 120–150 bardatasheet
Pre-atomiser tip only. Airmix is better for topcoats (official methods page).
Electrostatic
Brush
- Consumption
- 60–80 g/m²official
- Coats
- 3 coatsrecommended
Synthetic brush for waterborne, along the grain, don't overwork.
Process and compatibility
- Substrate preparation
- Sand bare wood P120–P150 on softwoods, P150–P180 on hardwoods; don't crush fibres with high roller pressure.datasheet
- Wood moisture
- 12–15 %recommended
- Goes over
- bare wood / XHC3 / XHT8–XHT19
- Sanding
- between coats P180–P220 by hand (Milesi C4/L3)datasheet
- Temperature and humidity
- Apply at +15…+25 °C, 50–75 % RH; never below +10 °C, not in direct sun, not on damp wood.recommended
- Don'ts
- don't thin with solvents
- don't let it freeze
- don't flood vertical work in one pass — it runs
- don't recoat inside 12 h (Milesi)
Storage
- Storage temperature
- +5…+30 °C, keep from frostrecommended
Safety: Waterborne: gloves and a spray mask when spraying, ventilate. Clean kit with water straight after use.
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- official: 3-in-1 (impregnation/primer/finish), XHT tinting, weather resistance, spray 80–100 g/m², brush 60–80 g/m²
- official listing: XGC06D Technocolor 60 gloss; XHT8–19 Milesi Hydrocrom impregnations on same page
- dealer search: no XGC products (2026-10-04)
- Milesi Hydrocrom guide p10: XGC 63 'finitura grano OP30' — thixotropic, penetrating, elastic, UV/weather resistant
- Milesi guide p6: spray/airmix/airless nozzle and pressure for Hydrocrom line
- Milesi guide p4: wood sanding grits, ≥ 90 µm dry film
- Milesi guide p12: XTC 2 anti-foam 0.1–1 %, XTC 3 retarder max 2 % for finishes
- Milesi cycles C1–C3 (XGC 63 in C2, C3)
- Milesi cycles C4–C6 (XGC 63 in C4: 125–150 g/m² min 12 h → P180–220 → 200–250 g/m² min 24 h)
- Milesi cycles L1–L3 (XGC 63 in all three)
- official methods page: airmix preferred for topcoats
Not covered by the sources
- solids content
- viscosity (cup) and density
- dust-free / touch / stack drying times for a single coat at 20 °C
- water dilution % (not published)
- XHT tint dose (official page names XHT but gives no %)
- shelf life and packaging sizes
- official confirmation that XGC06D is the Milesi XGC 6x 60-gloss version (inferred)
- safety data sheet
- not stocked on t-colormarket.ru — no dealer technical sheet
- no Technocolor or Milesi TDS PDF for XGC 06/63 found (web-search budget exhausted; Milesi guide used)