PPS01
PPS01 Fire-retardant white PU primer
Two-pack white polyurethane primer with fire-retardant additives for timber structures indoors. Fast drying, high solids (71 %), sands easily. When heated, the fire-retardant components break down and release a non-combustible gas that starves the fire of oxygen and slows flame spread. As the PPS01 primer + PPL01 enamel system it rates Group I fire-retardant efficiency to GOST R 53292-2009 (cl. 6.1). No official t-color.ru page - data from t-colormarket.ru and the Technocolor catalogues.
- fire protection / improved fire resistance of interior timber structures
- primer under the white fire-retardant enamel PPL01 (pigmented system, Group I)
- public interiors needing certified fire protection: wall panelling, doors, cladding, stairs
Mix calculator
Ask about PPS01
Answers are based on the PPS01 data and the products it mixes with.
Mixing matrix
- PC20Hardener% by weight: 50 %dealer% by volume: 60 %dealer
standard hardener (dealer and catalogue list PC20 only)
Fixed ratio - 50 % by weight, weigh it. By volume it's 60 %. Stir the base thoroughly first: the filler settles.
- PC60Hardener% by weight: 50 %catalog% by volume: ≈ 60 %recommended
allowed alternative per the fire-retardant leaflet - prefer PC20, as the dealer specifies
PC60 is non-yellowing; under white enamel that doesn't matter for a primer. The fire certification was most likely run on PC20 - confirm with Technocolor before swapping.
- S50Thinner% by weight: 20–30 (typ. 25) %dealer% by volume: 30–40 %dealer
universal, normal-evaporation thinner - the default
20 % for verticals and maximum build; 30 % if the gun spits on a 1.5-1.7 mm tip or it won't level on flats.
- S80Thinner% by weight: 20–30 %recommended
hot shop (above ~25 °C), large panels
Not from Technocolor documentation. More dust pick-up and sag risk on verticals.
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Hardener | PC20 | 50 %dealer | 60 %dealer | standard hardener (dealer and catalogue list PC20 only)Fixed ratio - 50 % by weight, weigh it. By volume it's 60 %. Stir the base thoroughly first: the filler settles. |
| Hardener | PC60 | 50 %catalog | ≈ 60 %recommended | allowed alternative per the fire-retardant leaflet - prefer PC20, as the dealer specifiesPC60 is non-yellowing; under white enamel that doesn't matter for a primer. The fire certification was most likely run on PC20 - confirm with Technocolor before swapping. |
| Thinner | S50 | 20–30 (typ. 25) %dealer | 30–40 %dealer | universal, normal-evaporation thinner - the default20 % for verticals and maximum build; 30 % if the gun spits on a 1.5-1.7 mm tip or it won't level on flats. |
| Thinner | S80 | 20–30 %recommended | — | hot shop (above ~25 °C), large panelsNot from Technocolor documentation. More dust pick-up and sag risk on verticals. |
Percentages are per 100 parts of component A.
Characteristics
- Solids
- 71 ± 1 %dealer
- Viscosity
- 23 ± 1 sdealer
- Pot life
- 3–4 hdealer
- Drying · Touch-dry
- 30 mindealer
- Drying · Fully dry
- 8 hdealer
- Drying · Before sanding
- ≈ 8 h (overnight safest) hrecommended
- Drying · Conditions
- 20 °C
- Fire retardancy
- Group I fire-retardant efficiency, GOST R 53292-2009 cl. 6.1dealer
- Properties
- fast drying; high solids; sands easilydealer
- Density
- ≈ 1.2-1.3 g/ml (part A) g/mlrecommended
- Thixotropy
- probably not strongly thixotropic; heavy-bodiedrecommended
Colours
- PPS01 · white
Application
HVLP
- Nozzle
- 1.8–2 mmrecommended
- Pressure · air
- 2–2.5 barrecommended
- Spray viscosity
- 20–26 s DIN4recommended
- Consumption
- 150 g/m²dealer
- Wet film
- ≈ 130-140 µmrecommended
- Coats
- 1 coat at 150 g/m² (the certified system figure) coatsrecommended
- Flash-off
- 10–20 minrecommended
- Recoat
- enamel (PPL01) after full dry 8 h and sandingrecommended
- Sanding between coats
- 280–320 grit Precommended
Spray, 150 g/m². 1.8-2.0 mm tip; a 1.5 mm won't atomise it well - if that's all you have, thin to 30 % S50 and accept less build per pass. 15-20 cm, 50 % overlap. Stir the base thoroughly before mixing.
Conventional spray
- Nozzle
- 1.8–2 mmrecommended
- Pressure · air
- 3–4 barrecommended
- Consumption
- 150 g/m²dealer
- Transfer efficiency
- up to 40 %official
Technocolor just says 'spray'. Transfer only up to 40 % (methods page) - mix more than you think.
Airmix (air-assisted airless)
- Nozzle
- 0.28–0.33 mmrecommended
- Pressure · fluid
- 50–90 barrecommended
- Pressure · air
- 1–2 barofficial
- Consumption
- 150 g/m²dealer
Not listed by Technocolor, but a normal way to shoot primer on panels and doors in production.
Airless
- Nozzle
- 0.33–0.38 mmrecommended
- Pressure · fluid
- 120–180 barrecommended
- Consumption
- 150 g/m²dealer
- Transfer efficiency
- up to 90 %official
Not listed by Technocolor. High transfer, easy to hit 150 g/m² in one pass; watch for sags on verticals.
Brush
- Why ru
- Дилер и оба каталога указывают только распыление.
Not recommended: Technocolor specifies spray only; a brush won't lay an even 150 g/m², which the fire rating depends on. Touch-up only.
Process and compatibility
- Substrate preparation
- Wood/MDF at 8-12 % MC, sanded P150-P180 (solid) or P180-P220 (MDF), de-dusted. No oil, wax or old finish - the fire rating assumes application to bare wood.recommended
- Goes over
- bare wood (interior timber structures) / bare MDF / wood boards
- Goes under
- PPL01
- Sanding
- 280–320 grit Precommended
- Don'ts
- don't eyeball the hardener - 50 % by weight
- don't use the mix past 3-4 h
- don't sand before full dry (8 h)
- don't skimp - below 150 g/m² per layer the fire rating isn't guaranteed
- don't topcoat with ordinary (non-fire-retardant) enamels if you need the certified system
- not for exterior use - interiors only
Storage
- Shelf life
- ≈ 12 months unopened monthsrecommended
- Storage temperature
- +5…+25 °C, sealed, away from heat/sparksrecommended
Used in finishing systems
Mixed into
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” comes from industry best practices (hover to see the reasoning).
- dealer product page: properties (fast dry, high solids, sands well), application, PC20 50/60 and S50 20-30/30-40 wt/vol, solids 71±1 %, viscosity 23±1 s CF-8, pot life 3-4 h, touch 30 min, full 8 h, 1/5/25 kg, 916 ₽/kg on order; re-verified 2026-10-05
- application methods: transfer efficiencies, airless ≤200 bar, airmix ≤20 bar fluid / 1-2 bar air
Not covered by the sources
- No official t-color.ru product page; no Technocolor TDS/SDS PDF found (web search budget exhausted this session; dealer search only returns the dealer page)
- Density not published (derived ≈1.2-1.3 g/ml)
- Volume % for PC60 option not published
- Sanding/stack time, dust-free time not published (only touch 30 min, full 8 h)
- Spray viscosity, nozzle and pressure not published (all derived)
- Shelf life and storage temperature not published
- Gloss of the primer not rated
- Whether the fire certification covers PC60 hardener (leaflet allows PC20/PC60 for the system; dealer lists PC20 only)
- Minimum dry-film thickness / number of coats required for the GOST R 53292 Group I rating beyond '150 g/m²'
- Hardness, chemical resistance, elasticity values not published
- Not used in any official finishing schedule (information/technology)