CPS24
CPS24 Solvent-borne pigment wood stain, cherry
Solvent-borne pigment wood stain, ready colour 'cherry'. High hiding power: evens out colour variation and masks defects, gives a calm natural tone; lightfast. Let down with S10/S12/S30/S90 at 200-1000 % (2-10 parts thinner per part stain). With binder it can be wiped on to highlight the pores of open-grain wood. Intermixes with the other CPS stains and solvent-borne stains.
- Staining furniture in any wood species
- Faux-cherry on pale woods (beech, birch, alder)
- Evening out colour variation in veneer and solid wood
- Pore highlighting on oak/ash (wipe-on with binder)
Mix calculator
Ask about CPS24
Answers are based on the CPS24 data and the products it mixes with.
Mixing matrix
- % by weight: 200–1000 %dealer% by volume: 200–1000 %dealer
S10 — fast, for fine-pore wood (beech, birch, maple, alder); S12 — medium, for medium-pore wood; S30 — fast general-purpose (catalog lists it for PU/acrylic/PE/UV; the dealer allows it for CPS24); S90 — slow, for open-grain wood (oak, ash) and big panels, gives more working time for wiping.
Main recipe for CPS24: 2-10 parts thinner to 1 part stain. More thinner = lighter, more transparent tone; dial it in on a sample board. The dealer labels them 'thinner / NC thinner / slow stain thinner'.
- % by weight: 500–1000 %catalog
S10 — fast, for fine-pore wood; S12 — medium evaporation, for medium-pore wood; S90 — slow evaporation, for open-pore wood (catalog thinner table).
2025/26 catalog figure for the whole CPS series (written for the concentrates). The 2022 catalog gave 500-2000 % for the series. For the CPS24 ready colour the dealer allows less thinning — from 200 %.
- CFS1Additive% by weight: 20–40 %dealer% by volume: 20–40 %dealer
Solvent binder — for wipe-on/pore-highlight work and to lock the pigment down before priming.
Taken from the sibling ready colours CPS22/CPS23; CPS24's own page lists no binder — test on an offcut.
- % by weight: 0–400 %catalog
Binders for the CPS series per the 2022 catalog: for spraying / roller / wiping.
- CFC3Additive% by weight: 200 %schedule
Roller-coating flat (anegre veneer) panels under a UV system, 60-80 g/m².
CFC3 is its own code from the UV schedule (stain binder for UV lines); no product page and not sold by the dealer. The schedule gives bare '%', not saying weight or volume.
- S90Thinner% by weight: 200 %schedule
UV schedule, roller application.
The schedule gives bare '%', not saying weight or volume.
- % by weight: intermixable; ratio set on a sample %catalog
Adjusting the cherry shade: stains in the series intermix with each other and with other solvent-borne stains (CTU). E.g. a touch of CPS9 (black) for a deeper, darker cherry, CPS1 (yellow) to warm it up.
Record ratios by weight.
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Thinner | S10 / S12 / S30 / S90 | 200–1000 %dealer | 200–1000 %dealer | S10 — fast, for fine-pore wood (beech, birch, maple, alder); S12 — medium, for medium-pore wood; S30 — fast general-purpose (catalog lists it for PU/acrylic/PE/UV; the dealer allows it for CPS24); S90 — slow, for open-grain wood (oak, ash) and big panels, gives more working time for wiping.Main recipe for CPS24: 2-10 parts thinner to 1 part stain. More thinner = lighter, more transparent tone; dial it in on a sample board. The dealer labels them 'thinner / NC thinner / slow stain thinner'. |
| Thinner | S10 / S12 / S90 | 500–1000 %catalog | — | S10 — fast, for fine-pore wood; S12 — medium evaporation, for medium-pore wood; S90 — slow evaporation, for open-pore wood (catalog thinner table).2025/26 catalog figure for the whole CPS series (written for the concentrates). The 2022 catalog gave 500-2000 % for the series. For the CPS24 ready colour the dealer allows less thinning — from 200 %. |
| Additive | CFS1 | 20–40 %dealer | 20–40 %dealer | Solvent binder — for wipe-on/pore-highlight work and to lock the pigment down before priming.Taken from the sibling ready colours CPS22/CPS23; CPS24's own page lists no binder — test on an offcut. |
| Additive | CFS1 / CFS3 / CFS4 | 0–400 %catalog | — | Binders for the CPS series per the 2022 catalog: for spraying / roller / wiping. |
| Additive | CFC3 | 200 %schedule | — | Roller-coating flat (anegre veneer) panels under a UV system, 60-80 g/m².CFC3 is its own code from the UV schedule (stain binder for UV lines); no product page and not sold by the dealer. The schedule gives bare '%', not saying weight or volume. |
| Thinner | S90 | 200 %schedule | — | UV schedule, roller application.The schedule gives bare '%', not saying weight or volume. |
| Additive | CPS1 / CPS2 / CPS3 / CPS8 / CPS9 / CPS10 / CPS22 / CPS23 / CPS25 | intermixable; ratio set on a sample %catalog | — | Adjusting the cherry shade: stains in the series intermix with each other and with other solvent-borne stains (CTU). E.g. a touch of CPS9 (black) for a deeper, darker cherry, CPS1 (yellow) to warm it up.Record ratios by weight. |
Percentages are per 100 parts of component A.
Characteristics
- Components
- 1K stain + thinner (optional binder)recommended
- Carrier
- solvent-borne (на основе растворителя, «ОР»)catalog
- Concentrate
- no — sold as a ready colour (not labelled «концентрат»), let down 200-1000 %recommended
- Lightfastness
- good (светостойкость)dealer
- Hiding
- high (высокая укрывная способность)catalog
- Levelling
- good (хорошая выравнивающая способность)dealer
- Pot life
- n/a (no hardener)recommended
- Gloss
- none (no film)recommended
- Drying · Conditions
- 20 °C
- Drying · Full dry (min)
- 20 mindealer
- Drying · Line flash-off (min)
- 5 minschedule
Colours
- CPS24 · cherry
Application
HVLP
- Nozzle
- 1.2–1.4 (typ. 1.3) mmrecommended
- Pressure · air
- 1.5–2 barrecommended
- Spray viscosity
- 10–12 s DIN4recommended
- Consumption
- 80–100 g/m²dealer
- Flash-off
- 20 mindealer
Stir thoroughly — the pigment settles. Keep shaking/stirring the cup while you work. Lay one even wet coat, no puddles; go lighter on end grain (it drinks more and goes darker). To wipe: spray, give it 1-3 min, then wipe along the grain with a sponge or lint-free rag, packing pigment into the pores (pore-highlight effect on open-grain wood — needs CFS1 binder).
Conventional spray
- Nozzle
- 1.2–1.4 (typ. 1.3) mmrecommended
- Pressure · air
- 2–3 barrecommended
- Spray viscosity
- 10–12 s DIN4recommended
- Consumption
- 80–100 g/m²dealer
More overspray than HVLP; hold the gun 20-25 cm off and spray in a well-extracted booth.
Cloth or pad
Spray, let it sit 1-3 min, then wipe along the grain with a sponge or lint-free rag to take off the excess (Technocolor's method definition). Wiping evens the tone and packs pigment into the pores — on oak/ash the pores go darker and the figure pops. Add CFS1 binder for a stronger effect and better pigment lock-down.
Roller coater (UV)
Flat parts on a roller-coater line only. In the official UV schedule the stain flashes 5 min at 20-25 °C before VTS20011 UV filler.
Airmix (air-assisted airless)
- Nozzle
- 09/40-11/40 tip (0.23-0.28 mm)recommended
- Pressure · fluid
- 8–15 barrecommended
- Pressure · air
- 1–2 barofficial
For production lines; HVLP is plenty in a workshop.
Process and compatibility
- Substrate preparation
- Sand P150 → P180 → P220, de-dust. On cherry/alder/birch (blotch-prone) don't go finer than P220 or the stain takes lighter and patchier.schedule
- Sanding
- Never sand the stain itself. Sand only the first primer coat (P280-P320); if you cut through to the stain, touch it up.recommended
- Temperature and humidity
- 15-25 °C, RH ≤ 75 %recommended
Storage
- Packaging
- 1 л / 5 лdealer
Used in finishing systems
Mixed into
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” comes from industry best practices (hover to see the reasoning).
- dealer CPS24: properties, uses, methods + rates, thinners S10/S12/S30/S90 200-1000 % by weight and volume, full dry 20 min, packs/prices (re-fetched 2026-10-05)
- dealer CPS22 (sibling ready colour): CFS1 20-40 %
- dealer CPS037: finishing instruction stain → PTS20 → PTL20 SM
- official CPS9 page (series properties)
- 2022 catalog: CFS1/3/4 binders 0-400 %
- UV anegre panel schedule: CPS 100 / CFC3 200 / S90 200, 60-80 g/m², 5 min
- application methods (airmix pressures, wiping definition)
Not covered by the sources
- no official t-color.ru page for CPS24
- no Technocolor TDS/SDS PDF found (web-search budget exhausted this run; family run also found none)
- solids %
- viscosity as supplied
- density
- drying times other than 'full dry 20 min'
- binder ratio specific to CPS24 (CFS1 20-40 % taken from CPS22/23)
- S30 suitability only on dealer page (catalog lists S30 for PU/acrylic/PE/UV, not stains)
- shelf life
- storage temperature
- packaging unit conflict (label kg vs measure l)
- conflict: thinner 200-1000 % (dealer, CPS24) vs 500-1000 % (2025 catalog, series)
- CFC3 (UV-schedule stain binder) has no product page/TDS; schedule ratio basis (weight vs volume) not stated
- 2022 catalog gives the CPS series 500-2000 % thinner (vs 500-1000 % in 2025/26)